SMALL DEVICES FOR TUBULAR SNAP-ON (WITH CLIP) OR WALL-MOUNTED VERSION

Multi-sensor-components help to get fully automatic functions for buildings. They do not require costly programming, operation or handling, they work strictly decentralized and maintenance-free.

In the lighting technique they combine light comfort with a maximum amount of energy saving. The installation is made either directly on the lights fixtures with a min. 60mm wide by means of a snap-clip on the fluorescent lamps or in wall-mounted or wall-recessed boxes.

The items are suitable for all lamps, can be operated in combination with electronic ballasts or transformers with 1-10V interface as well as with all kind of KOBALD-Dimmers for incandescent lamps, high voltage halogen lamps, low voltage halogen lamps with conventional transformers or electronic transformers.

The type MS-LRS is suitable for non-dimmable lighting systems.

The following components are 5 devices with different functions:

MSD

Multi-Sensor-Dimmer - Constant Light Control with presence detector and adjustment for desired level on the device

The Multi-Sensor-Dimmer MSD and MSD-T are intended for light controls on a workplace or one room.

• control of the room brightness by descending daylight
• switching OFF by sufficient daylight or persons absence
• automatic switch ON by persons presence and insufficient daylight
• 1-10V output for control of electronic ballasts, transformers and power dimmers
• integrated powerful relay-switch (5A)

The adjustment of the desired light level is made directly on the device itself, there is no need for any other parts.

• it can simply be integrated on the existing lighting installations when using dimmable electronic ballasts
• fully automatic, no operation necessary
• use in rooms in which the light level should not change
• presence detector can be switched off

MSD-T

Multi-Sensor-Dimmer with extern dimming value adjustment and controlling through pushbutton / Constant light control with presence detection and pushbutton dimming value adjustment

By MSD-T the adjustment of light level are made through a remotely connected control button. Therefore the pre-selected light level can be easily changed.

• changing the dimming light level manually is easily possible anytime
• stored light level are kept and can be retrieved if device switches ON again
• use in rooms in which the lighting should be also manually changeable

MSL

Multi-Sensor with light level reduction or switch-function, soft level-change with presence detection, alternatively switch function in dependence of persons presence or intensity of ambient light

The MSL light level reduction is made for presence dependent control from a higher light level (at presence) to a lower light level (at absence). It can be used alternatively for presence dependent switching of the lighting or any other load.

• 1-10V output for control of electronic ballasts, transformers and power dimmers
• powerful relay-output (5A) for direct switching of loads (switch function)
• a brightness level, at which no switch ON will take place, can be pre-selected
• the adjustment of the light level is made directly on the device itself, there is no need to use any further operation elements.

• it can simply be integrated in the existing lighting installations when using dimmable electronic ballasts or transformers
• fully automatic, no operation necessary
• use in areas in which automatic switch OFF is needed and by persons presence a higher light level is needed, e.g. corridors or sales areas/rooms
• the switch function of the device can be used for non-dimmable lamps or other loads

MS-LRS

Multi-Sensor with a function of Light Level-Control Switch
Presence and light level dependent switching for non-dimmable lighting

The light level switch MSL is designed for presence and light level dependent switching of lightings.

• powerful relay-output (5A) for direct switching of non-dim fluorescent lamps (conventional ballasts and electronic ballasts) as well as incandescent lamps and halogen lamps
• switching OFF by sufficient daylight or absence
• re-switching ON by insufficient daylight and presence
• the adjustment of light level can be made alternatively on the device itself or an extern potentiometer.
• manual ON/OFF with an extern push-button is possible.

• can simply be installed in existing lighting installations
• use in rooms in which the lightings will or can not be dimmed, e.g. corridors, lobbies, stockrooms, offices, and classrooms
• use in existing lighting installations for switching of fluorescent lamps with conventional ballasts or electronic ballasts

Accessories:

Motion detector KBM and Light + Motion sensors LBS/e
Additional presence recognition for the Multi-Sensor-Components

• additional switch contact (10A load) with its own delay time adjustment after ending a presence recognition
• can be connected to all Multi-Sensor-Components, additional motion detector is not necessary
• can be used universally for switching of heaters, air condition etc. or for presence monitoring.